cfinch
02-28-2006, 11:10 PM
1st chassis is a 93 coupe that I was going to put my ls1 in... Car is completely stripped and has a 6 point roll cage in it and a custom firewall/tranny tunnel to accomodate a motor beneath the dash which was gonna be an ls1 built by Garageworks. I'm just going a different route... The cage alone cost me $1,000 and I'm asking for the car as is rolling chassis $1,000
http://i28.photobucket.com/albums/c239/cfinch702/coupe5.jpg
http://i28.photobucket.com/albums/c239/cfinch702/coupe4.jpg
http://i28.photobucket.com/albums/c239/cfinch702/coupe2.jpg
2nd is a rhd s13 hatch I had bought from baby a while back. The car has a full roll cage and the engine bay is stitch welded along with the frame rails. The car has no rust other than some minor surface rust and comes as a rolling chassis. Comes with a clean rhd dash, door panels, ps line etc... basicly all the little things necissary for a rhd car. Asking $1,500
http://dfinch.bizland.com/180sx1.JPG
http://dfinch.bizland.com/180sx4.JPG
http://dfinch.bizland.com/180sx5.JPG
http://dfinch.bizland.com/180sx6.JPG
Next is my fully built sr20 built by r&d
eagle rods
ross pistons stock bore 8:1
total seal rings
new oem bearings
fully ported/polished head
262/262 webcams
ferrea valves 1mm oversized
r&d valve springs
ti retainers
jwt cam gears
cometic headgasket
arp headstuds
new waterpump
greddy oil pan
ported stock intake manifold
Engine has been fully assembled by garageworks and hasn't even been installed in a car yet... Yet again I'm going another route so I got this to sell... Motor will come read to drop in. Asking $3000
http://i28.photobucket.com/albums/c239/cfinch702/builtsr2.jpg
http://i28.photobucket.com/albums/c239/cfinch702/builtsr1.jpg
Next up is my ls1 swap... I had plans on putting it in my coupe and I got the mounts to drop it into a 240sx but the motor has to sit back under the dash... comes complete with a t56 6 speed transmission, ecu, harness etc... Pulled from a running 99 camaro with 70k on it. $3,500 No pics but I can get some...
I got a set of jic flta2's for the s13... Barely driven on only tracked twice and are in perfect working order $1,000
I also have some other cars I'm interested in selling... I have no pics right now but if you have any interest you can contact me and I will go further into a description... I got a 95 240sx 5 speed base model super clean, 91 s13 coupe se model 5 speed, 91 s13 hatch se 5 speed... All those cars when I get pictures I'll post but I'm gonna want decent money for them cause they are all either very clean or have alot of new parts on them but mostly stock...
Everything is located in either Apple Valley, California at my house or Garageworks in Palmdale, California.
email me at [email protected]
http://i28.photobucket.com/albums/c239/cfinch702/coupe5.jpg
http://i28.photobucket.com/albums/c239/cfinch702/coupe4.jpg
http://i28.photobucket.com/albums/c239/cfinch702/coupe2.jpg
2nd is a rhd s13 hatch I had bought from baby a while back. The car has a full roll cage and the engine bay is stitch welded along with the frame rails. The car has no rust other than some minor surface rust and comes as a rolling chassis. Comes with a clean rhd dash, door panels, ps line etc... basicly all the little things necissary for a rhd car. Asking $1,500
http://dfinch.bizland.com/180sx1.JPG
http://dfinch.bizland.com/180sx4.JPG
http://dfinch.bizland.com/180sx5.JPG
http://dfinch.bizland.com/180sx6.JPG
Next is my fully built sr20 built by r&d
eagle rods
ross pistons stock bore 8:1
total seal rings
new oem bearings
fully ported/polished head
262/262 webcams
ferrea valves 1mm oversized
r&d valve springs
ti retainers
jwt cam gears
cometic headgasket
arp headstuds
new waterpump
greddy oil pan
ported stock intake manifold
Engine has been fully assembled by garageworks and hasn't even been installed in a car yet... Yet again I'm going another route so I got this to sell... Motor will come read to drop in. Asking $3000
http://i28.photobucket.com/albums/c239/cfinch702/builtsr2.jpg
http://i28.photobucket.com/albums/c239/cfinch702/builtsr1.jpg
Next up is my ls1 swap... I had plans on putting it in my coupe and I got the mounts to drop it into a 240sx but the motor has to sit back under the dash... comes complete with a t56 6 speed transmission, ecu, harness etc... Pulled from a running 99 camaro with 70k on it. $3,500 No pics but I can get some...
I got a set of jic flta2's for the s13... Barely driven on only tracked twice and are in perfect working order $1,000
I also have some other cars I'm interested in selling... I have no pics right now but if you have any interest you can contact me and I will go further into a description... I got a 95 240sx 5 speed base model super clean, 91 s13 coupe se model 5 speed, 91 s13 hatch se 5 speed... All those cars when I get pictures I'll post but I'm gonna want decent money for them cause they are all either very clean or have alot of new parts on them but mostly stock...
Everything is located in either Apple Valley, California at my house or Garageworks in Palmdale, California.
email me at [email protected]