uzriha
02-04-2006, 08:22 PM
hey guys,
I'm trying to sell my project 240sx here.
Attending purdue university with CS major takes a lot of time.
It is hard for me to let this 240sx collect dusts.
I don't think i will have a time until summer so.
I wish this car goes to a good home....
pictures.
http://photobucket.com/albums/f332/uzriha/
note
The car is currently not in running condition.
s14 chassis 88k miles
stock s13 engine
- less than 20k miles got it from my trust worthy friend.
- turbo has no shaft play.
s15 front end conversion
parts
- light, rad support, fender, bumper w/ fog light.
- hood is carbon fiber but painted black pearl as car.
- don't like body kits. so all stock s15 parts. sleeper.
labor and painted the car
- have proof of 2900.
Blitz lm intercooler
Blitz air intake core type.
Blitz NUR spec exhaust
HKS SSQV w/ greddy hot pipe -
Tein Flex w/ EDFC -
RPS stage 2 clutch & fly wheel -
5zigen 17' w/ dunlop -
300zx MAF
300zx break, rotor, pad
walbro f. pump
KOYO radiator
Samco hoses.
2 s13 ecu
2 engine harness
part that you might want from me.
Greddy pulley kit.
HKS 88mm HG
Tomei 12.5 270 cams
Tomei fuel rail
JUN con. rod
autronic sm2
autronic 500r
autronic nissan triger disk
autronic fuel relay
stoptech break system. sd-40, 4 piston. whole set.
s13 engine block with
- darton sleeve new crank and new bearing.
I will have getting tomei springs set up (B)
which is double spring setup and ti. retainers. w/RAS
i was going to do 88mm bore up
and gt35 setup, but i just don't have time to do it.
I'm sure i'm missing some parts in the list. I will add some stuff up.
I'm located at indiana.
contact me to [email protected] please.
thanks.
I'm trying to sell my project 240sx here.
Attending purdue university with CS major takes a lot of time.
It is hard for me to let this 240sx collect dusts.
I don't think i will have a time until summer so.
I wish this car goes to a good home....
pictures.
http://photobucket.com/albums/f332/uzriha/
note
The car is currently not in running condition.
s14 chassis 88k miles
stock s13 engine
- less than 20k miles got it from my trust worthy friend.
- turbo has no shaft play.
s15 front end conversion
parts
- light, rad support, fender, bumper w/ fog light.
- hood is carbon fiber but painted black pearl as car.
- don't like body kits. so all stock s15 parts. sleeper.
labor and painted the car
- have proof of 2900.
Blitz lm intercooler
Blitz air intake core type.
Blitz NUR spec exhaust
HKS SSQV w/ greddy hot pipe -
Tein Flex w/ EDFC -
RPS stage 2 clutch & fly wheel -
5zigen 17' w/ dunlop -
300zx MAF
300zx break, rotor, pad
walbro f. pump
KOYO radiator
Samco hoses.
2 s13 ecu
2 engine harness
part that you might want from me.
Greddy pulley kit.
HKS 88mm HG
Tomei 12.5 270 cams
Tomei fuel rail
JUN con. rod
autronic sm2
autronic 500r
autronic nissan triger disk
autronic fuel relay
stoptech break system. sd-40, 4 piston. whole set.
s13 engine block with
- darton sleeve new crank and new bearing.
I will have getting tomei springs set up (B)
which is double spring setup and ti. retainers. w/RAS
i was going to do 88mm bore up
and gt35 setup, but i just don't have time to do it.
I'm sure i'm missing some parts in the list. I will add some stuff up.
I'm located at indiana.
contact me to [email protected] please.
thanks.